Hard water contains calcium and magnesium minerals, due to which it does not provide a natural water feel. The mineral composition can protect your bones and heart. Besides it, the hard water form a mineral deposition on silverware and glasses, discolor the sink and harming the pipes. At the same time, there is no significant adverse effect of hard water on health.
In comparison, soft water provides the actual taste of water without harming your utensils. It can increase the life of your plumbing. So it is a great idea to install a water softener at home to free from all these problems.
The water softener must be located in sideboards, basements, or sheltered places. It must be a place where it can be draining.
Different Installation Steps:
- Read the instructions for your water softener system.
- Turn off all the water sources at home.
- Switch on all the faucets and hoses to clear out the water lines before activating the water softener.
- Place your water purifier in a smooth and leveled area.
- Estimate the length between bypass ports and cold water lines on the water softener tank by measuring tape.
- Slat the copper tube of measured length and solder attachments on the ends.
- Obey the instructions for discharge tube installation on the water softener head.
- Operate the overflow tube connected with the water conditioner tank’s side and the discharge tube to the end.
- Place the bypass valve onto the head valve of a water conditioner.
- It would help if you connected copper tubing that conveys water to the bypass valve. The wrench is used to tightening the supply tube nuts. During the water softener is installed, don’t wrench the screws too tight.
- Connect the copper tubing to the water lines by the water conditioner. You must solder pipes’ fittings during water conditioner installation by applying flux and liquefy with a propane torch.
- Rotate the electric heater and the water to the house back on.
- Place about 4 gallons of water into the brine tank and plug the control valve. 40lbs of potassium chloride salt must be added to the unit.
- Open the water supplier’s valve to the one-forth position to maintain oxygen level in the drain line. Place the conditioner into the backwash stage and put the bypass valve into the system.
- During the steady stream of water appears at the drain, then on the water supply valve.
- During water softener installation, operate the conditioner from the complete backwash cycle.
- Check the leaks of the system.
Installation of Salt-Based Water Softener
- Turn off the water supply sources at home. Clear out the water pipes.
- Close the heater of hot water and its power.
- A water softener must be installed before the water heater line, so locate the mainline.
- Slash into the mainline by pipe cutter.
- Insert an elbow fitting in the pipe to supply the filter that holds a bypass valve to provide water around the filter.
- Estimate the pipe size that will take to the bypass valve taking the estimations from the unit.
- Secure the pipes to the unit through fittings.
- Press the hose to the unit, then supply it to drain. The hose’s end will be at least 2-3inches above the drain’s hole to drop the water’s back siphoning.
- Attach the overflow tube with the brine tank.
- Rotate the valve to the bypass location and drain water to remove any debris or sediment.
Installation of a Salt-Free System
- Arrange the sections of the system in the selected area to install a water softener.
- Turn off the water sources that supply water. Drain the water from the pipes.
- The line Holds the pipe on the cold water supply, then takes the line to the pre-filter housing.
- Secure a shut-off valve with the line, either by soldering it with copper or gluing it to PVC.
- Connect a carbon pre-filter after the shut-off valve, connecting it through compression fittings.
- After the pre-filter second shut-off valve is introduced, expand the pipe to the filter system’s distribution head. Attach it with a compression fitting.
- To flow the water through the system and back by the house, attach the system’s downflow outlet back to the cold water supply pipe.
- Shut off both shut-off valves and turn on the water supply source.
Installation of a Magnetic System
- Select the area for water softener installation.
- The magnet box may hook on one side, permitting it to suppress over the pipe.
- Insert the box around the pipe and align according to the direction so that the box’s water flows in the right direction.
- Close the box throughout the line and fixed it with the screw.
Installation of a Reverse Osmosis System
- Turn off the water under the sink and turn on the faucet above to clear out the water from the lines.
- Select the place to install filter assembly.
- Insert the saddle valve with the filter and fit the cold water feed above the saddle valve.
- Secure one end of the water supply with the saddle valve.
- Connect the supply and drain lines to the tap that comes from the system.
- Secure the fixture to the sink and connect the drain line adapter.
- Fit storage tank and attach the supply lines.
- Inspect for leaks.
Cost for Water Softener Installation
Your unit size must be according to your home size. RO plant is too costly to afford, so most people install the smallest category in their faucet. The cost will depend on the water that has to be filtered. Companies out can install the water softener and take charge of it according to unit size. If anyone is not acknowledged about their installation process or is not confident to install it, you can hire a pro. So it is better to install the magnetic system. However, some systems cost differently. Salt and non-salt ways of filtering systems costs are the same. While in a salt-based system, there will be a charge of salts included in the total price.
Further, you will have to pay him according to the installation time consumption in hiring the pro. Magnetic systems are simple to install and can easily be installed at home. There cost on its size and size of the pipe for connection.
Hey! Do You Wanna Buy Best Water Softener System Then Click Me.
Conclusion
There are several water softeners available in the market. Deciding which water softener to install will depend on your requirement and budget. Most of the magnetic and salt-based systems cost the same according to the supply and installation process. The cost of reverse osmosis is high as it filters out impurities and contains more parts than the other systems suggest it is expensive to install and maintain. The water softener installation process for all systems is considered easy, but you need to follow some instructions during installation.